Skip to main content

Silver Treatments on Glass Tutorial - First Published on Artisan Whimsey

Silver Treatments on Glass Beads


There are many ways to add silver to your glass beads!  I'll list a few here today, if you have any other suggestions, please post them in the comments! I'm always looking for new ideas!

The first way to add silver to your glass beads is with fine silver wire.  I'm not sure why, but you are supposed to use fine silver wire as opposed to the silver jewelry wire you might have on hand.  I order my fine silver wire from Monsterslayer.  I like them and they always have up-to-date pricing as the silver market is so volatile lately.  I use 30 gauge silver wire, but there are different gauges available.  I like 30 gauge because it's more delicate.  If you want to use higher gauge wire, you can get different effects, like actually placing thought-out dots on your bead!  

I cut easily usable lengths of silver wire (about 9 inches or so) and clip the hemos at the measure I want to use.  If I'm applying it to a round bead, I usually clip at about 2-3 inches.  Fine silver wire will disappear in your flame, so make sure you work waaaaaaaaaaaaaaay out at the end of the flame.  Barely touch the silver wire to the bead under the flame, move the bead away, and quickly wrap the wire around the bead.  When you've reached the end of your clipped wire, flame cut the silver, and then very delicately melt the silver wire at the end of the flame into the bead.  This is how you get the trailing dots.  Here's a photo of beads I made with silver wire:


Next is using silver foil.  You can use silver foil, or silver leaf.  I like silver foil, because it's easier to handle and easier to cut with a scissors.  If you use leaf, you just have to be more careful with it, as it can easily blow around your bench due to your ventilation system, or passers-by!  I buy packets of 25 sheets of silver foil, usually from Robin Koza of Glass Diversions.  I cut the single sheet into the sizes I want (for a 12mm bead I usually use an eighth of a sheet).  Place your silver foil on your graphite marver, or other surface you use, on your bench.  When you are done making your bead, heat up the outside of the bead very slightly, and roll it on the marver to accept the foil.  Burnish it onto the bead (make sure your bead is not mushy!) with a tool - I use my brass stump shaper.  Then reintroduce the bead into the flame at the very end; you just want to melt the silver foil into the bead, not make the bead hot or mushy again.  Here's a photo of some beads I made with silver foil:

To make beads with silver foil and frit, just apply the silver foil as above.  When you are done with the above steps, heat the bead up again hot enough to accept the frit, roll the bead in frit, and melt it in as you usually do!  Here's a photo of a silver foil and frit bead!

Finally, I'll talk about silvered ivory stringer (SIS).  I enjoy this method, and there are many ways you can do it.  I'll just tell you about two of mine.  The first way I make SIS is to waft a one inch section at the end of an ivory rod in the flame, until it's hot enough to accept the silver foil.  Burnish the silver foil on with your torch mounted graphite marver, and then you are ready to pull stringer!  Melt a small blob on the end of the rod - here's where it's important to burnish very well, so the silver does not just disappear.  Pull with a tweezer or other pulling tool, and set aside on your table until cool enough to touch.  When you want to use it, hold your bead under the flame near the top, barely touch the end of the stringer in the flame and attach where you want it on your bead.  Then, under the flame but still in some heat, wrap the stringer until you are happy.  Flame cut or snap off!  Here's some beads with SIS:

And finally, you can make dots with SIS as well!  For this method, I like to use commercially pulled 2-3mm ivory stringer.  I simply wet my fingers with saliva and run them at the top of a stringer, and wrap the piece of foil around it.  You may have to wet your fingers multiple times to get the foil to stay.  I know, it sounds gross, but it works.  And it's not so gross!  You melt the germs off!  When I'm ready to use the stringer, I melt a very small blog at the end of the stringer rod, and apply to the bead just like any dot of glass.  To make round dots, use your brass stump shaper and push the dot gently into the bead, this will keep it round.  Then melt in as usual.  Here's a photo of beads using this method:

I hope you enjoyed this little post on silver.  There are many different designs you can do with silver - add enamel, baking soda, etc.  Again, if you have any other methods, I'd love to hear about them.  How about encasing silver wire?  Silver powder? 

Please find me and my beads at SueBeads etsy, SueBeads web site, and SueBeads blog!

Comments

I love the touches of silver on glass!!
As I am not a lamowork artist, I found this post so interesting! This is why I buy handmade beads! Beautiful work here, Sue!

Popular posts from this blog

Bead Soup Blog Party!

Welcome to the 3rd Bead Soup Blog Party! What is a Bead Soup Blog Party? Each beader was paired up with another jewelry designer and tasked with sending the following: ~ A focal ~ A special clasp (not just a lobster claw) ~ Some coordinating spacers or beads Using the focal and the clasp was mandatory, but we could use anything from our own stash to round out the rest, and choose to use the coordinating beads or not. You may recall my partner was Margot Potter ; click this link to see the blog post I wrote of what she sent me! Here's what I made! Dangly earrings! Come see what the rest of us made! 1. Lori Anderson, Pretty Things 2. Kitty Durmaj, Perles and Life 3. Michelle Heim, Life In the Bead Lane 4. Lisa Petrillo, Lucid Moon Studio 5. Anitra Gordy, Leelu Creations 6. Paige Maxim, Paige Maxim Designs 7. Marianna Boylan, Pretty Shiny Things 8. Cheryl Roe, BeadRoe 9. Heidi Post, Ex Post Facto 10. Cindy Wimmer, Sweet Bead Studio 11. Terri Gauthier, Blooming Ideas 12.

The Tacky Earring Blog Hop

Diana Ptaszynski had a great idea, instead of a Tacky Christmas Sweater blog hop, a Tacky Holiday Earring blog hop! I was on it.  I had ideas right away.  I had so many I had to control myself.  You can buy these for $15 each, too!  Here we go! I found these awesome wreaths in the miniature Christmas section in Michaels, and they go perfectly with silver and copper colored plastic beads! These trees were found in Michaels, on an end-cap - I assume they are scrapbook or card making supplies, but make fantastic earrings.  The holes were a little small and far down, so I had to make LARGE loops.  Paired these with cute little gold colored jingle bells! And, finally, the ones I had in my head the moment she announced the blog hop.  Dr. Seuss sparkly puff balls with ribbons.  The only thing that would have made these better for me is if I could have found the red ribbons I really wanted to pair these with - don't get me wrong, the silver is cool and all, but in my head they w